Journal of Powder Materials

Kyung-Sik Oh

3 Articles

Microstructural Evolution and Properties in Ti(CN)-Co/Ni Cermet Depending on the Starting Material for Incorporation of WC: Tai-Joo Chung, Sun-Yong Ahn, Seung-Su Ahn, Myung-Soo Shin, Hak-Kyu Kim, Kyung-Bae Kim, Kyung-Sik Oh, Hyuk-Jae Lee; J Korean Powder Metall Inst. 2007;14(2):132-139.; DOI: https://doi.org/10.4150/KPMI.2007.14.2.132

15 View
0 Download
1 Citations

In the Ti(CN)-Co/Ni cermet, WC is an effective additive for increasing sinterability and mechanical properties such as toughness and hardness. In this work, WC, (WTi)C and (WTi)(CN) were used as the source of WC and their effects were investigated in the respect of microstructural evolution and mechanical properties. Regardless of the kinds of WC sources, the hard phase with dark core and bright rim structure was observed in the Ti(CN)-Co/Ni cermet under the incorporation of relatively small amount of WC. However, hard phases with bright core began to appear and their frequency increased with the increase of all kinds of WC source addition. The ratio of bright core to dark one in the (TiW)(CN)-Co/Ni cermet was greatest under the incorporation of (WTi)C compared at the same equivalent amount of WC. The mechanical properties were improved with the addition of WC irrespective of the kinds of sources, but the addition of (WTi)(CN) was less effective for the increase of fracture toughness.

Citations

Citations to this article as recorded by

Investigation into the microstructure and cutting performance of (Ti,Ta,W)(CN)–Co/Ni cermets
Se-Woong Oh, Sun-Yong Ahn, Kyung-Sik Oh, Hyukjae Lee, Tai-Joo Chung
International Journal of Refractory Metals and Hard Materials.2015; 53: 36. CrossRef

Effect of Grain Size and Heat-treating Atmosphere on the Phase Stability of Y-TZP: Tai-Joo Chung, Seung-Su Ahn, Eun-Wha Song, Kyung-Sik Oh, Jong-Sook Lee, Young-Sik Kim; J Korean Powder Metall Inst. 2006;13(5):360-365.; DOI: https://doi.org/10.4150/KPMI.2006.13.5.360

20 View
0 Download
1 Citations

Abstract PDF

The phase stability of tetragonal phase in Y-TZP was investigated in terms of the distribution of grain sizes and heat-treating atmosphere. Y-TZP with various grain sizes were prepared using duration time at 1600°C as experimental parameter. Accumulated grain size distributions were built from the SEM micrographs and the amount of tetragonal phase were measured using XRD. Both results were compared to determine the critical grain size before and after heat-treatment in vacuum. The critical grain size drastically decreased compared with the small increase of average grain size due to the autocatalytic effect which critically affects the tetragonal to monoclinic phase transformation. After heat-treatment in reductive atmosphere critical grain size relatively increased due to the stabilization of tetragonal phase. The formation of oxygen vacancies during heat-treatment was ascribed to the increase of stability.

Citations

Citations to this article as recorded by

Direct Observation on the Low Temperature Degradation Due to Surface Treatment in Y-TZP
Tai-Joo Chung, Hye-Sung Kim
Journal of Korean Powder Metallurgy Institute.2010; 17(3): 197. CrossRef

Fabrication of Ag doped Hydroxyapatite and its Antimicrobial Effects with the Particle Size: Kyung-Sik Oh, Kyung-Ja Kim, Young-Keun Jeong; J Korean Powder Metall Inst. 2001;8(3):192-196.

6 View
0 Download

Abstract PDF: Ag doped Hydroxyapatite powder in nano-scale was successfully synthesized either by co-precipitation or by ion exchange route. The fabricated powder was successfully dispersed through freeze drying due to the prevention of secondary particles. The antimicrobial effects of nano-HAp against E.coli was superior to micron ones not only in its strength but also in duration.

Author index